Carburetor Adjustment Initial1. Turn adjustment needle clockwise until it makes light contact with the seat. Do not force. 2. The initial setting of a
Remove CarburetorModels 91200 92200, 942001. Remove air cleaner assembly. 2. Move throttle (top) lever to idle position. Note: On fixed adjustable co
Remove Fuel Tank from Carburetor 1. Remove remaining screws holding fuel tank onto carburetor. 2. Remove screw holding fuel tank bracket to cylinde
Adjustable Pulsa-Jet Carburetors with Choke-A-Matic®, Manual or Remote Choke, Models 60000, 80000, 90000, 100000, 110000, 130000These Pulsa-Jet carbu
High Altitude Compensation(except Low Emissions Carburetors) Note: If engine is operated at high altitudes, performance may decrease. If poor
Final AdjustmentLow Emissions Carburetors (with type numbers ending in A1 through A9 or E1 through E9) 1. Start and run engine for five minutes to war
Assemble Carburetor to Fuel Tank 1. Place new tank gasket on fuel tank. 2. Lower carburetor into fuel tank and install mounting screws closest to ch
Assemble CarburetorInstall Welch Plug1. Place a small amount of non-hardening sealant such as Permatex® II or nail polish around outside edge of
Stamped Throttle Shaft1. Press in new rubber throttle shaft seal with sealing lip down until seal bottoms. 2. Place new foam seal on throttle and i
Assemble Choke-A-Matic® LinkageRotary Choke1. Insert "Z" bend of Choke-A-Matic® linkage into same hole as return spring. 2. Slide washer
Disassemble Carburetor Remove Throttle Plate & Shaft 1. Remove throttle plate screw and throttle plate, Fig. 63. 2. After removal of throttle plat
Assemble CarburetorFuel Pump1. Smooth side of cup must rest against diaphragm, Fig. 77. This prevents spring from cutting diaphragm. 2. When insta
Disassemble Carburetor Remove Adjustment Needle & Seat 1. Remove needle to inspect. 2. Replace needle if needle is bent, grooved, or broken, Fi
Disassemble Fuel Pump1. Remove fuel pump cover, diaphragm, spring and cup, Fig. 71. 2. Inspect diaphragm for punctures, cracks and fatigue. Repl
Models 91200 92200, 942001. Remove air cleaner assembly. 2. Move throttle (top) lever to idle position. Note: On fixed adjustable control panels, ben
Remove Fuel Tank from Carburetor 1. Remove remaining screws holding fuel tank onto carburetor. 2. Remove screw holding fuel tank bracket to cylinde
Models 80200, 82200, 90200, 91200, 92200, 94200, 112200, 130200, 132200, 135200, 136200, 137200Fixed jet Pulsa-Jet carburetors have been made in thre
Assemble Choke-A-Matic® LinkageRotary Choke 1. Insert "Z" bend of Choke-A-Matic® linkage into same hole as return spring. 2. Slide washer
Install SpiralWhen inserting spiral, top must be flush to 1/32" (.8 mm) below carburetor flange, and spiral parallel with fuel tank mounting surf
Install Throttle Shaft & Plate Stamped Throttle Shaft1. Press in new rubber throttle shaft seal with sealing lip down until seal bottoms. 2. Pl
Disassemble Choke-A-Matic® Linkage Rotary Choke1. To remove choke link, remove speed adjustment lever and stop switch insulator plate. 2. Work lin
Disassemble Carburetor Remove Throttle Plate & Shaft 1. Remove throttle plate screw and throttle plate, Fig. 63. 2. After removal of throttle plat
Disassemble Carburetor Remove adjustment needle and Seat 1. Remove adjustment needle to inspect. 2. Replace needle valve if needle is bent, grooved, o
Disassemble Fuel Pump1. Remove fuel pump cover, diaphragm, spring and cup, Fig. 71. 2. Inspect diaphragm for punctures, cracks and fatigue. Repl
Komentarze do niniejszej Instrukcji